Bürkert寶德流量計接頭種類及特性
更新時間：2018-02-13 點擊次數：1820次
Bürkert寶德流量計接頭種類及特性
Bürkert類型
產品照片Typ S030
類型S030
INLINE傳感器與槳葉輪進行流量測量
DN06到DN65
封閉的管道系統，傳感器內部配件
四分之一轉技術
變送器可用于指示，監控，傳輸，開/關控制，批量控制
傳感器配件S030內置槳輪來測量流量。當液體流經管道時，槳葉輪會產生脈沖，其頻率與流量成正比。 Bürkert“INLINE Quarter-turn技術”是一種確保...
Bürkert類型
?產品照片Typ S030
類型S030
INLINE傳感器與槳葉輪進行流量測量
DN06到DN65
封閉的管道系統，傳感器內部配件
四分之一轉技術
變送器可用于指示，監控，傳輸，開/關控制，批量控制
Bürkert類型
?產品照片類型SE32
類型SE32
變送器用于INLINE傳感器安裝
與帶有葉輪的INLINE傳感器配件S030兼容，用于流量測量（參見數據表類型8032，S030）
與帶有橢圓齒輪的INLINE傳感器配件S077進行流量測量（參見數據表類型SE32 + S077）
Bürkert類型
?產品照片Typ S010
類型S010
INLINE傳感器與葉片配合
用于連接到用于流量檢測的SE10變送器（參見數據表流量開關8010型
Bürkert類型
?產品照片Typ S012
鍵入S012
適合槳輪流量傳感器
用于連接變送器類型SE11或類型SE12用于流量測量（參見數據表流量計類型8012和8011）
用于安裝到DN06 ... DN65的所有管道或流體塊系統中
Bürkert類型
?產品照片Typ S020
類型S020
插入配件用于流量或分析測量
適用于插入式測量設備的純凈，侵蝕性或受污染液體
大范圍的過程連接：PVC，PP，PVDF，PE，不銹鋼，黃銅的DN06至DN400
變送器可用于： - 指示，監測，傳輸 - 關/關控制，批量控制
Bürkert類型
?產品照片Typ S022
類型S022
適用于ELEMENT pH和電阻率電導率測量設備
適用于8202型和8222型ELEMENT發射機的通用適配器，適用于純粹，腐蝕性或污染性液體
適應標準管道系統或將BürkertS020接頭轉換為S022接頭
管道直徑從DN 06（減少）到DN 110（塑料）或更大（不銹鋼）
Bürkert類型
?產品照片Typ S039
類型S039
帶光學測量原理的變送器的INLINE傳感器與槳葉輪配合使用
用于連接SE39型變送器進行流量測量（參見數據表流量計型號8039）
用于安裝到DN06 ... DN50的所有管道中
Bürkert寶德流量計接頭種類及特性
Bürkert type
Type S030
INLINE sensor-fitting with paddle wheel for flow measurement
- DN06 to DN65
- Closed pipe system, sensor inside fitting
- Quarter-turn technology
- Transmitter available for Indication, Monitoring, Transmitting, On/Off control, Batch control
The sensor-fitting S030 has a built-in paddle wheel to measure the flow rate. When liquid flows through the pipe, the paddle wheel is set in rotation producing pulses which frequency is proportional to the flow rate. The Bürkert “INLINE Quarter-turn technology” is a construction ensuring a...
Get more information
Bürkert type
Type S030
INLINE sensor-fitting with paddle wheel for flow measurement
- DN06 to DN65
- Closed pipe system, sensor inside fitting
- Quarter-turn technology
- Transmitter available for Indication, Monitoring, Transmitting, On/Off control, Batch control
Bürkert type
Type SE32
Transmitter for INLINE sensor-fitting
- Compatible with INLINE sensor-fitting S030 with paddle wheel for flow measurement (see datasheets types 8032, S030)
- Compatible with INLINE sensor-fitting S077 with oval gears for flow measurement (see datasheet type SE32+S077)
Bürkert type
Type S010
INLINE sensor-fitting with blade
- For connection to a transmitter type SE10 for flow detection (see datasheet flow switch type 8010
Bürkert type
Type S012
Fitting for paddle wheel flow sensors
- For connection to a transmitter type SE11 or type SE12 for flow measurement (see datasheets Flowmeter types 8012 and 8011)
- For installation into all pipes from DN06…DN65 or in fluid block systems
Bürkert type
Type S020
Insertion fitting for flow or analytical measurement
- Universal fitting for Insertion measuring device in pure, aggressive or contaminated liquids
- Large range of process connections: DN06 to DN400 in PVC, PP, PVDF, PE, stainless steel, brass
- Transmitter available for: - Indication, Monitoring, Transmitting -On/Off control, Batch control
Bürkert type
Type S022
Fitting for ELEMENT pH and resistive conductivity measurement devices
- Universal adaptor for type 8202 and 8222 ELEMENT transmitters in pure, aggressive or contaminated liquids
- Adaptation into standard piping systems or conversion of Bürkert S020 fittings into S022 fittings
- Pipe diameters from DN 06 (with reduction) up to DN 110 (plastic) or bigger (Stainless steel)
Bürkert type
Type S039
INLINE sensor-fitting with paddle wheel for transmitter with optical measuring principle
- For connection to a transmitter type SE39 for flow measurement (see datasheet flowmeter type 8039)
- For installation into all pipes from DN06…DN50
Bürkert type
Type S051
Magnetic-inductive flow-rate sensor, low flow rates
- For connection to a transmitter type SE56 (blind in compact version or with display in compact or remote version) for flow measurement (see datasheets types 8051 and SE56)
- Clean in place (CIP)
- Low-flow measurements on from 3 l/h
Bürkert type
Type S054
Magnetic inductive sensor with wafer connection for water treatment and general purpose applications
- For connection to a transmitter type SE56 (blind in compact version or with display in compact or remote version) for flow measurement (see datasheets types 8054/8055 and SE56)
Bürkert type
Type S055
Magnetic inductive sensor with flanges for water treatment and general purpose applications
- For connection to a transmitter type SE56 (blind in compact version or with display in compact or remote version) for flow measurement (see datasheets types 8054/8055 and SE56)
Bürkert type
Type S056
Magnetic inductive sensor with hygienic process connections
- For connection to a transmitter type SE56 (blind in compact version or with display in compact or remote version) for flow measurement (see datasheets types 8056 and SE56)
- Sanitary version, 3A certificate
- Dedicated to food & beverage or pharmaceutical applications
- Low-flow measurements on from 3 l/h
Bürkert type
Type S070
Inline oval wheel sensor
- DN 15 to 100
- INLINE Quarter-Turn technology
- Electronics for indication, monitoring, transmitting, On/Off control and batch control
Bürkert寶德流量計接頭種類及特性
